Designjet 4500 Error Codes

  • 01.0:03 error –  Error Impact 12C Channel
  • 01.0:10 error –  Problem With The Gamut PCI PCA
  • 01.1:10 error –  Problem Wuth The PrintMech PCA
  • 01.2:10 error –  ISS PCA Faulty – Humidity Sensor Out Of Scale Or NVM Backup Failure
  • 02:10 error –  Encoder Seems To Be Wrong
  • 02.1:10 error –  Problem With The Carriage PCA
  • 03:10 error –  Problem With The Power Supply Unit
  • 05.1:10 error –  CPU Fan Is Stoppede Or Burnt
  • 05.3:10 error –  Main Memory Size Failure
  • 06:03 error –  NVM File Has Bad CRC
  • 06:10 error –  Main NVM Failure – Not Detected, Read/Write Failed Or Readback Error
  • 07:10 error –  Aerosol Fan Drive Burnt
  • 08:10 error –  Problem With Front Panel
  • 1:10 error –  Trailing Cable Does Not Seem To Be Detected
  • 13.n:10 error –  Problem Starting Acumen Supplies
  • 21:03 error –  Service Station Servo Shutdown
  • 21:12 error –  Fail Moving Service Station
  • 21:13 error –  Problem With The Service Station
  • 23:10 error –  Problem With The APS
  • 24:03 error –  Ink Setup faiure(Ink Supply Tubes Purge Failed)
  • 24:10 error –  Broken Bag Detected in Ink Cartridge
  • 26.0:01 error –  Bad Contact Detected In ISS Slot – 0 Floater
  • 26.1:01 error –  Bad Contact Detected In ISS Slot 1 Floater
  • 26.2:01 error –  Bad Contact Detected In ISS Slot 2 Floater
  • 26.3:01 error –  Bad Contact Detected In ISS Slot 3 Floater
  • 26.n:10 error –  Order Of Ink Supplies Incorrect
  • 26:14 error –  A Wrong Ink Cartridge Has Been Detected
  • 27:03 error –  An Error Has Occurred In Printhead Detection
  • 27:14 error –  A Wrong Printhead Has Been Detected
  • 29.0:01 error –  Printhead Cleaner Not Inserted Correctly In Slot 1
  • 29.1:01 error –  Printhead Cleaner Not Inserted Correctly In Slot 2
  • 29.2:01 error –  Printhead Cleaner Not Inserted Correctly In Slot 3
  • 29.3:01 error –  Printhead Cleaner Not Inserted Correctly In Slot 4
  • 29.4:01 error –  Printhead Cleaner Not Inserted Correctly In Slot 5
  • 29.5:01 error –  Printhead Cleaner Not Inserted Correctly In Slot – 6
  • 29.6:01 error –  Printhead Cleaner Not Inserted Correctly In Slot 7
  • 29.7:01 error –  Printhead Cleaner Not Inserted Correctly In Slot 8
  • 41:03   error –  Electrical Current Limit In Media-Axis Motor
  • 41:10   error –  Electrical Fault In Media-Axis Motor
  • 42:03   error –  Elecrtical Current Limit In Scan-Axis Motor
  • 42:10   error –  Electrical Fault In Scan-Axis Motor
  • 43:10   error –  Vacuum Fan Has Stopped Functioning
  • 44:10   error –  Problem With The Aerosol Fan
  • 44:11   error –  Aerosol Fan Not Connected
  • 51:10   error –  Window Sensor Failure
  • 51.1:10   error –  PHC Access Door Sensor Failure
  • 52:10   error –  Drop Detector Switch On/Off Failure
  • 53:10   error – Media Sensor Failure
  • 54:10   error – Media Lever Sensor Failure
  • 55:10   error – Problem With The Line Sensor
  • 56:03   error – Analog Encoder Calibration Failed
  • 56:10   error – Analog Encoder Calibration Failed
  • 61:01   error – The File Format Is Incorrect And The Printer Cannot Process The Job
  • 61:04.1   error – The Postscript Fonts Are Missing. Upgrade The Firmware
  • 61:08.1   error – The File Cannot Be Printed Because It Is Password Protected
  • 63:04  error – Input/Output Problem Through The Network Card
  • 64:04  error – Input/Output Problem Through The USB Port Request a repair estimate
  • 65:04   error – Input/Output Problem Through An Unknown Port
  • 66:08   error – Cannot Print File On Current Paper Type. The Paper Type Has Changed Since The File Was Sent
  • 67:04  error – Input/Output Problem Through a Fireware Port
  • 68:03 error – Non-critical permanent data was lost. This does not prevent the printer working, only that internal life counters will not be recorded untill the printer is restarted
  • 71:03 error – Out of memory failure
  • 71:04 error – Out of memory failure
  • 71:19 error – Defult serial Number found in the main and back uo NVM. It seems that both the Ink Supply and Hard Disk Drive have been replaced together
  • 72:04 error – Generic Firmware error
  • 73:03 error – Servo error
  • 74:00 error – Failed getting part number/serial number
  • 74:01 error – Error uploading firmware
  • 74:04 error – Old vacuum fan detected – upgrade the firmware
  • 76:03 error – Out of disk space – data was lost
  • 77:04 error – Embedded web server internal software error
  • 79:03 error – Generic firmware error
  • 79:04 error – Generic firmware error
  • 79.1:04 error – CDS server lost connection with client
  • 81:01 error – Paper servo shutdown
  • 81:03 error – It was impossible to correctly stop the servo before setting the encoder position
  • 81:10 error – Fail starting paper motor
  • 85:03 error – Problem finding the drive roller zero
  • 86:01 error – Carriage servo shutdown
  • 86:03 error – Scan-axis lenght test failure
  • 86:10 error – Initialising scan-axis motor failure
  • 86:11 error – Scan-axis length too short
  • 91:10 error – Repeated printhead issue
  • 93:11 error – Unable to pressurise the IDS
  • 98:02 error – Switching to lower performance due to printhead quality
Message us now