Designjet 4000 Error Codes

  • 01.0:03  – Error Impact 12C Channel
  • 01.0:10 – Problem With The Gamut PCI PCA
  • 01.1:10  – Problem Wuth The PrintMech PCA
  • 01.2:10  – ISS PCA Faulty – Humidity Sensor Out Of Scale Or NVM Backup Failure
  • 02:10  – Encoder Seems To Be Wrong
  • 02.1:10  – Problem With The Carriage PCA
  • 03:10  – Problem With The Power Supply Unit
  • 05.1:10 – CPU Fan Is Stoppede Or Burnt
  • 05.3:10  – Main Memory Size Failure
  • 06:03  – NVM File Has Bad CRC
  • 06:10  –  Main NVM Failure – Not Detected, Read/Write Failed Or Readback Error
  • 07:10  – Aerosol Fan Drive Burnt
  • 08:10  – Problem With Front Panel
  • 11:10  – Trailing Cable Does Not Seem To Be Detected
  • 13.n:10  – Problem Starting Acumen Supplies
  • 21:03  – Service Station Servo Shutdown
  • 21:12 – Fail Moving Service Station
  • 23:10  – Problem With The APS
  • 24:03  – Ink Setup faiure(Ink Supply Tubes Purge Failed)
  • 24:10  – Broken Bag Detected in Ink Cartridge
  • 26.0:01 – Bad Contact Detected In ISS Slot – 0 Floater
  • 26.1:01 – Bad Contact Detected In ISS Slot 1 Floater
  • 26.2:01 – Bad Contact Detected In ISS Slot 2 Floater
  • 26.3:01 – Bad Contact Detected In ISS Slot 3 Floater
  • 26.n:10 – Order Of Ink Supplies Incorrect
  • 26:14  – A Wrong Ink Cartridge Has Been Detected
  • 27:03 – An Error Has Occurred In Printhead Detection
  • 27:14 – A Wrong Printhead Has Been Detected
  • 29.0:01 – Printhead Cleaner Not Inserted Correctly In Slot 1
  • 29.1:01 – Printhead Cleaner Not Inserted Correctly In Slot 2
  • 29.2:01 – Printhead Cleaner Not Inserted Correctly In Slot 3
  • 29.3:01 – Printhead Cleaner Not Inserted Correctly In Slot 4
  • 29.4:01 – Printhead Cleaner Not Inserted Correctly In Slot 5
  • 29.5:01 – Printhead Cleaner Not Inserted Correctly In Slot 6
  • 29.6:01 – Printhead Cleaner Not Inserted Correctly In Slot 7
  • 29.7:01 – Printhead Cleaner Not Inserted Correctly In Slot 8
  • 41:03 – Electrical Current Limit In Media-Axis Motor
  • 41:10 – Electrical Fault In Media-Axis Motor
  • 42:03 – Elecrtical Current Limit In Scan-Axis Motor
  • 42:10 – Electrical Fault In Scan-Axis Motor
  • 43:10 –  Vacuum Fan Has Stoped Functioning
  • 44:10 – Problem With The Aerosol Fan
  • 44:11 – Aerosol Fan Not Connected
  • 51:10 –  Window Sensor Failure
  • 51.1:10 – PHC Access Door Sensor Failure
  • 52:10 – Drop Detector Switch On/Off Failure
  • 53:10 – Media Sensor Failure
  • 54:10 – Media Lever Sensor failure
  • 55:10 – Problem With The Line Sensor
  • 56:03 – Analog Encoder Calibration Failed
  • 56:10 – Analog Encoder Calibration Failed
  • 61:01 – The File Format Is Incorrect And The Printer Cannot Process The Job
  • 61:04.1 – The Postscript Fonts Are Missing. Upgrade The Firmware
  • 61:08.1 – The File Cannot Be Printed Because It Is Password Protected. Request a repair estimate
  • 63:04  – Input/Output Problem Through The Network Card
  • 64:04 –  Input/Output Problem Through The USB Port
  • 65:04 – Input/Output Problem Through An Unknown Port
  • 66:08 – Cannot Print File On Current Paper Type. The Paper Type Has Changed Since The File Was Sent
  • 67:04 – Input/Output Problem Through a Fireware Port
  • 68:03 – Non-critical permanent data was lost. This does not prevent the printer working, only that internal life counters will not be recorded untill the printer is restarted
  • 71:03 – Out of memory failure
  • 71:04 – Out of memory failure
  • 71:19 – Defult serial Number found in the main and back uo NVM. It seems that both the Ink Supply and Hard Disk Drive have been replaced together
  • 72:04 – Generic Firmware error
  • 73:03 – Servo error
  • 74:00 – Failed getting part number/serial number
  • 74:01 – Error uploading firmware
  • 74:04 – Old vacuum fan detected – upgrade the firmware
  • 76:03 – Out of disk space – data was lost
  • 77:04 – Embedded web server internal software error
  • 79:03 – Generic firmware error
  • 79:04 – Generic firmware error
  • 79.1:04 – CDS server lost connection with client
  • 81:01 – Paper servo shutdown
  • 81:03 –  It was impossible to correctly stop the servo before setting the encoder position
  • 81:10  – Fail starting paper motor
  • 85:03 – Problem finding the drive roller zero
  • 86:01 –  Carriage servo shutdown
  • 86:03 –  Scan-axis lenght test failure
  • 86:10 –  Initialising scan-axis motor failure
  • 86:11 –  Scan-axis length too short
  • 91:10 –  Repeated printhead issue
  • 93:11 –  Unable to pressurise the IDS
  • 98:02 –  Switching to lower performance due to printhead quality
Message us now