Designjet 1050 & Designjet 1055 Error Codes

  • 0B0000 error – Bad Ambient Temperature Measured
  • 0B0001 error – Bad Humidity Read
  • 0B0002 error – Bad IDS Pressure Read
  • 0B0003 error – ACDO Intrenal Channles Check Failure
  • 0B0004 error – Unable To Detect Pump
  • 0B0005 error – Unable To Detect Valve
  • 0B0006 error – Trailing Cable Incorrectly Connected OR Fuse In Electronics Module Has Burned
  • 0B0007 error – Unable To Detect Vacuum Fan
  • 0B0008 error – >Unable To Detect Cooling Fan
  • 0B0009 error – Unable To Detect Aerosol Fan (Including On Right Cover)
  • 0B000A error – Primer Shut Down Error
  • 0B000B error -Pump Or Pressure Sensor Not Working
  • 0B000C error – Serial Device ADC Test Failure
  • 0B000D error – 24 V Source Test Faiulre
  • 0B000E error – Short Circuit In Scan-Axis Motor
  • 0000D8 error – External Library Error
  • 01002D error – The Main PCA Cannot Communicate With The Carriage
  • 010020 error – FirmWare DIMM Test Failure
  • 010021 error – Memory Module Test Failure
  • 010023 error – EEROM Test Failure
  • 010028 error – EEROM Checksum Failure
  • 010029 error – EEROM Write Failure
  • 010040 error – Error In Paper-Axis Encoder Quadrature
  • 010041 error – Error In Scan-Axis Encoder Quadrature
  • 010042 error – Error In Service Station-Axis Encoder Quadrature
  • 010050 error – PostScript Processing Error
  • 01009X error – Error In Paper-Axis Motor Encoder
  • 02xxxx error – PostScript/Firmware Error
  • 04Cxxx error – EIO Accessories (EIO Card/Hard Disk Drive) Error
  • 048xxx error – EIO Card Is From A Third Party Vendor May Not Be Fully Compliant With IIO Protocol Specification2.0 OR EIO Card Firmware Is Not Updated
  • 048500 error – There Are Too Many EIO Cards Connected To Printer
  • 060300 error – One Of The Printheads Has Internal Electrical Problem
  • 060301 error – One Of The Printheads Has Internal Electrical Problem
  • 060305 error – Thermal Shutdown Error(One Of The Printheads Has Gone Above Maximum Teperture)
  • 060306 error – Problem With Printhead Selection
  • 060307 error – APA Regulation Failure
  • 060308 error – APA Regulation Failure
  • 060309 error – Problem With Setting The Voltage Of Printheads
  • 06030A error – Error In Finding The Mark Encoder
  • 06030B error – The Ambient Temperture Measured Is Out Of The Normal Range
  • 070100 error – Firmware Error
  • 080001 error – PostScript Error
  • 09xxxx error – EIO Accessories (EIO Card/Hard Disk Drive) Error
  • 09Axxx error – Internal Error
  • 09A001 error – There Are Too Many Hard Disk Drives Connected To The Printer
  • 09Bxxx error – Internal Error
  • 09Cxxx error – Internal Error
  • 0A0000 error – The Air Pressure Is Below The Minimum Requirement
  • 0A0010 error – Problem In Pressurizing The Air System
  • 0A0020 error – Error In Cabrating The APS Sensor
  • 0A0030 error – Problem In Depressurizing Air System
  • 0A0040 error – Ink Tubes Initialization Failure Due To Low Air Pressure
  • 0A0050 error – The Printer Has Detected A Leak In The Tubes System Before The Life Of The System
  • 0A0060 error – The Printer Has Detected A Leak In The Tubes System After The Life Of The System
  • 0A0070 error – The Backup EEROM Contents Stored In The Tubes Systems Are Not Consistent With The Ones Required By The Firmware
  • 0C0030 error – Bad Drop Detector
  • 0C0032 error – Drop Detector Not Calibrated For All Printheads
  • 0C1000 error – Primer Not Calibrated
  • 0C1001 error – Primer Shutdown Error
  • 0D00 error – System Error Code Related To The Multi-roll Feeder
Message us now