| 01.0:03 error – Error Impact 12C Channel |
| 01.0:10 error – Problem With The Gamut PCI PCA |
| 01.1:10 error – Problem Wuth The PrintMech PCA |
| 01.2:10 error – ISS PCA Faulty – Humidity Sensor Out Of Scale Or NVM Backup Failure |
| 02:10 error – Encoder Seems To Be Wrong |
| 02.1:10 error – Problem With The Carriage PCA |
| 03:10 error – Problem With The Power Supply Unit |
| 05.1:10 error – CPU Fan Is Stoppede Or Burnt |
| 05.3:10 error – Main Memory Size Failure |
| 06:03 error – NVM File Has Bad CRC |
| 06:10 error – Main NVM Failure – Not Detected, Read/Write Failed Or Readback Error |
| 07:10 error – Aerosol Fan Drive Burnt |
| 08:10 error – Problem With Front Panel |
| 1:10 error – Trailing Cable Does Not Seem To Be Detected |
| 13.n:10 error – Problem Starting Acumen Supplies |
| 21:03 error – Service Station Servo Shutdown |
| 21:12 error – Fail Moving Service Station |
| 21:13 error – Problem With The Service Station |
| 23:10 error – Problem With The APS |
| 24:03 error – Ink Setup faiure(Ink Supply Tubes Purge Failed) |
| 24:10 error – Broken Bag Detected in Ink Cartridge |
| 26.0:01 error – Bad Contact Detected In ISS Slot – 0 Floater |
| 26.1:01 error – Bad Contact Detected In ISS Slot 1 Floater |
| 26.2:01 error – Bad Contact Detected In ISS Slot 2 Floater |
| 26.3:01 error – Bad Contact Detected In ISS Slot 3 Floater |
| 26.n:10 error – Order Of Ink Supplies Incorrect |
| 26:14 error – A Wrong Ink Cartridge Has Been Detected |
| 27:03 error – An Error Has Occurred In Printhead Detection |
| 27:14 error – A Wrong Printhead Has Been Detected |
| 29.0:01 error – Printhead Cleaner Not Inserted Correctly In Slot 1 |
| 29.1:01 error – Printhead Cleaner Not Inserted Correctly In Slot 2 |
| 29.2:01 error – Printhead Cleaner Not Inserted Correctly In Slot 3 |
| 29.3:01 error – Printhead Cleaner Not Inserted Correctly In Slot 4 |
| 29.4:01 error – Printhead Cleaner Not Inserted Correctly In Slot 5 |
| 29.5:01 error – Printhead Cleaner Not Inserted Correctly In Slot – 6 |
| 29.6:01 error – Printhead Cleaner Not Inserted Correctly In Slot 7 |
| 29.7:01 error – Printhead Cleaner Not Inserted Correctly In Slot 8 |
| 41:03 error – Electrical Current Limit In Media-Axis Motor |
| 41:10 error – Electrical Fault In Media-Axis Motor |
| 42:03 error – Elecrtical Current Limit In Scan-Axis Motor |
| 42:10 error – Electrical Fault In Scan-Axis Motor |
| 43:10 error – Vacuum Fan Has Stopped Functioning |
| 44:10 error – Problem With The Aerosol Fan |
| 44:11 error – Aerosol Fan Not Connected |
| 51:10 error – Window Sensor Failure |
| 51.1:10 error – PHC Access Door Sensor Failure |
| 52:10 error – Drop Detector Switch On/Off Failure |
| 53:10 error – Media Sensor Failure |
| 54:10 error – Media Lever Sensor Failure |
| 55:10 error – Problem With The Line Sensor |
| 56:03 error – Analog Encoder Calibration Failed |
| 56:10 error – Analog Encoder Calibration Failed |
| 61:01 error – The File Format Is Incorrect And The Printer Cannot Process The Job |
| 61:04.1 error – The Postscript Fonts Are Missing. Upgrade The Firmware |
| 61:08.1 error – The File Cannot Be Printed Because It Is Password Protected |
| 63:04 error – Input/Output Problem Through The Network Card |
| 64:04 error – Input/Output Problem Through The USB Port Request a repair estimate |
| 65:04 error – Input/Output Problem Through An Unknown Port |
| 66:08 error – Cannot Print File On Current Paper Type. The Paper Type Has Changed Since The File Was Sent |
| 67:04 error – Input/Output Problem Through a Fireware Port |
| 68:03 error – Non-critical permanent data was lost. This does not prevent the printer working, only that internal life counters will not be recorded untill the printer is restarted |
| 71:03 error – Out of memory failure |
| 71:04 error – Out of memory failure |
| 71:19 error – Defult serial Number found in the main and back uo NVM. It seems that both the Ink Supply and Hard Disk Drive have been replaced together |
| 72:04 error – Generic Firmware error |
| 73:03 error – Servo error |
| 74:00 error – Failed getting part number/serial number |
| 74:01 error – Error uploading firmware |
| 74:04 error – Old vacuum fan detected – upgrade the firmware |
| 76:03 error – Out of disk space – data was lost |
| 77:04 error – Embedded web server internal software error |
| 79:03 error – Generic firmware error |
| 79:04 error – Generic firmware error |
| 79.1:04 error – CDS server lost connection with client |
| 81:01 error – Paper servo shutdown |
| 81:03 error – It was impossible to correctly stop the servo before setting the encoder position |
| 81:10 error – Fail starting paper motor |
| 85:03 error – Problem finding the drive roller zero |
| 86:01 error – Carriage servo shutdown |
| 86:03 error – Scan-axis lenght test failure |
| 86:10 error – Initialising scan-axis motor failure |
| 86:11 error – Scan-axis length too short |
| 91:10 error – Repeated printhead issue |
| 93:11 error – Unable to pressurise the IDS |
| 98:02 error – Switching to lower performance due to printhead quality |
