Designjet 2000, 2500CP, 3000, 3500CP Error Codes

Designjet 2000 – 010020 error The CheckSum Read On The Flash SIMM Is InCorrect
Designjet 2000 – 010021 error The Base DRAM Or The RAM SIMM Tests Failed
Designjet 2000 – 010022 error The SWATH RAM Test Failed
Designjet 2000 – 010023 error A Fuse On The Main PCA Has Blown
Designjet 2000 – 010025 error Problem Initializing The Encoder Pulse Generator
Designjet 2000 – 010030 error One Of The Two Interconnect Boards Not Detected
Designjet 2000 – 010031 error The Printhead Primitive Driver ASIC Test Failed
Designjet 2000 – 010032 error Fan Test Failed – Current Not Detected In One Or Both Fans
Designjet 2000 – 010033 error The DC Motor ASIC Test Failed
Designjet 2000 – 010034 error One Of The DC Motor Has Failed
Designjet 2000 – 010035 error One Of The Stepper Motors Has Failed
Designjet 2000 – 010036 error ADC Test Failure In The Main PCA
Designjet 2000 – 010037 error ADC Test Failure In The Carriage PCA
Designjet 2000 – 010038 error A Printhead Voltage Could Not Be Set – Main PCA Failure
Designjet 2000 – 010039 error A Printhead Voltage Could Not Be Set – Carriage PCA Failure
Designjet 2000 – 010040 error The Amnient Temperture Measured Is Out Of The Normal Range
Designjet 2000 – 010041 error Problem In Setting The Printhead Voltage
Designjet 2000 – 010042 error The Status Of One Of The Optical Sensors Is Not Stable When It Should Be
Designjet 2000 – 010100 error Error Reading In The EEROM
Designjet 2000 – 010101 error An Action Outside The EEROM Limits Has Been Performed
Designjet 2000 – 010102 error Physical EEROM Write And/Or Write Operations Failed. The EEROM Data That Is Written Does Not Match The Data That Is Read
Designjet 2000 – 010110 error The Content Of The Permanent Configuration Area Of The EEROM Is Not Valid When The Printer Is initialised In Service Mode
Designjet 2000 – 010111 error The Content Of The User Configuration Area EEROM Is Not Valid When The Printer Is initialised
Designjet 2000 – 010120 error The Content Of The Permanent Configuration Area Of The EERom Is Not Valid When Printer Is initialised In Normal Mode
Designjet 2000 – 010121 error One Of The Banks Of The User Area Was Corrupted While Writing Or Reading In That Area
Designjet 2000 – 020000 error Error In Finding The Primer Home Position
Designjet 2000 – 020001 error Error In Finding The Elevator Home Position
Designjet 2000 – 020002 error Error In Finding The Refill Arm Home Position
Designjet 2000 – 020003 error Error In Finding The refill Stepper Motor Home Position
Designjet 2000 – 020004 error Error In Finding The Service Station Home Position
Designjet 2000 – 020005 error Elevator Has A Problem Reaching A Desired Position
Designjet 2000 – 020006 error The Refill Position In The Y-axis In Not Calibrated
Designjet 2000 – 020010 error Problem With Fine Movement of The Y-Axis Motor
Designjet 2000 – 020011 error Error During Initialization Of The Y-Axis
Designjet 2000 – 040xxx error MIO Card Error
Designjet 2000 – 040601 error The MIO Card Does Not Support The MIO – 6 Protocol Cards With Vision – 5 Or Below Can Not Be Used With The Plotter. Version – 5.1 Cards Behave As Expected But Does Not Support PML Intructions
Designjet 2000 – 050000 error The Line Sensor Has Problems Finding The Mark Encoder
Designjet 2000 – 060000 error Th Line Sensor Is Not Functioning Properly Because There Is To Much Ambient Light
Designjet 2000 – 060200 error Incompatible Firmware And Carriage PCA
Designjet 2000 – 060399 error Incompatible Firmware And Line Sensor
Designjet 2000 – 07xxxx error Firmware Error
Designjet 2000 – 08xxxx error PostScript Error
Designjet 2000 – 080001 error Hard Disk Drive Installed Without PostScript
Designjet 2000 – 09xxxx error Problem With The Hard Disk
Designjet 2000 – 09004 error PostScript Installed Without The Hard Disk Drive
Designjet 2500 – 010020 error The CheckSum Read On The Flash SIMM Is InCorrect
Designjet 2500 – 010021 error The Base DRAM Or The RAM SIMM Tests Failed
Designjet 2500 – 010022 error The SWATH RAM Test Failed
Designjet 2500 – 010023 error A Fuse On The Main PCA Has Blown
Designjet 2500 – 010025 error Problem Initializing The Encoder Pulse Generator
Designjet 2500 – 010030 error One Of The Two Interconnect Boards Not Detected
Designjet 2500 – 010031 error The Printhead Primitive Driver ASIC Test Failed
Designjet 2500 – 010032 error Fan Test Failed – Current Not Detected In One Or Both Fans
Designjet 2500 – 010033 error The DC Motor ASIC Test Failed
Designjet 2500 – 010034 error One Of The DC Motor Has Failed
Designjet 2500 – 010035 error One Of The Stepper Motors Has Failed
Designjet 2500 – 010036 error ADC Test Failure In The Main PCA
Designjet 2500 – 010037 error ADC Test Failure In The Carriage PCA
Designjet 2500 – 010038 error A Printhead Voltage Could Not Be Set – Main PCA Failure
Designjet 2500 – 010039 error A Printhead Voltage Could Not Be Set – Carriage PCA Failure
Designjet 2500 – 010040 error The Amnient Temperture Measured Is Out Of The Normal Range
Designjet 2500 – 010041 error Problem In Setting The Printhead Voltage
Designjet 2500 – 010042 error The Status Of One Of The Optical Sensors Is Not Stable When It Should Be
Designjet 2500 – 010100 error Error Reading In The EEROM
Designjet 2500 – 010101 error An Action Outside The EEROM Limits Has Been Performed
Designjet 2500 – 010102 error Physical EEROM Write And/Or Write Operations Failed. The EEROM Data That Is Written Does Not Match The Data That Is Read
Designjet 2500 – 010110 error The Content Of The Permanent Configuration Area Of The EEROM Is Not Valid When The Printer Is Initialised In Service Mode
Designjet 2500 – 010111 error The Content Of The User Configuration Area EEROM Is Not Valid When The Printer Is initialised
Designjet 2500 – 010120 error The Content Of The Permanent Configuration Area Of The EERom Is Not Valid When Printer Is initialised In Normal Mode
Designjet 2500 – 010121 error One Of The Banks Of The User Area Was Corrupted While Writing Or Reading In That Area
Designjet 2500 – 025000 error Error In Finding The Primer Home Position
Designjet 2500 – 025001 error Error In Finding The Elevator Home Position
Designjet 2500 – 025002 error Error In Finding The Refill Arm Home Position
Designjet 2500 – 025003 error Error In Finding The refill Stepper Motor Home Position
Designjet 2500 – 025004 error Error In Finding The Service Station Home Position
Designjet 2500 – 025005 error Elevator Has A Problem Reaching A Desired Position
Designjet 2500 – 025006 error The Refill Position In The Y-axis In Not Calibrated
Designjet 2500 – 020010 error Problem With Fine Movement of The Y-Axis Motor
Designjet 2500 – 020011 error Error During Initialization Of The Y-Axis
Designjet 2500 – 040xxx error MIO Card Error
Designjet 2500 – 040601 error The MIO Card Does Not Support The MIO – 6 Protocol Cards With Vision – 5 Or Below Can Not Be Used With The Plotter. Version – 5.1 Cards Behave As Expected But Does Not Support PML Intructions
Designjet 2500 – 050000 error The Line Sensor Has Problems Finding The Mark Encoder
Designjet 2500 – 060000 error Th Line Sensor Is Not Functioning Properly Because There Is To Much Ambient Light
Designjet 2500 – 060200 error Incompatible Firmware And Carriage PCA
Designjet 2500 – 060399 error Incompatible Firmware And Line Sensor
Designjet 2500 – 07xxxx error Firmware Error
Designjet 2500 – 08xxxx error PostScript Error
Designjet 2500 – 080001 error Hard Disk Drive Installed Without PostScript
Designjet 2500 – 09xxxx error Problem With The Hard Disk
Designjet 2500 – 09004 error PostScript Installed Without The Hard Disk Drive
Designjet 3000 – 010020 error The CheckSum Read On The Flash SIMM Is InCorrect
Designjet 3000 – 010021 error The Base DRAM Or The RAM SIMM Tests Failed
Designjet 3000 – 010022 error The SWATH RAM Test Failed
Designjet 3000 – 010023 error A Fuse On The Main PCA Has Blown
Designjet 3000 – 010025 error Problem Initializing The Encoder Pulse Generator
Designjet 3000 – 010030 error One Of The Two Interconnect Boards Not Detected
Designjet 3000 – 010031 error The Printhead Primitive Driver ASIC Test Failed
Designjet 3000 – 010032 error Fan Test Failed – Current Not Detected In One Or Both Fans
Designjet 3000 – 010033 error The DC Motor ASIC Test Failed
Designjet 3000 – 010034 error One Of The DC Motor Has Failed
Designjet 3000 – 010035 error One Of The Stepper Motors Has Failed
Designjet 3000 – 010036 error ADC Test Failure In The Main PCA
Designjet 3000 – 010037 error ADC Test Failure In The Carriage PCA
Designjet 3000 – 010038 error A Printhead Voltage Could Not Be Set – Main PCA Failure
Designjet 3000 – 010039 error A Printhead Voltage Could Not Be Set – Carriage PCA Failure
Designjet 3000 – 010040 error The Amnient Temperture Measured Is Out Of The Normal Range
Designjet 3000 – 010041 error Problem In Setting The Printhead Voltage
Designjet 3000 – 010042 error The Status Of One Of The Optical Sensors Is Not Stable When It Should Be
Designjet 3000 – 010100 error Error Reading In The EEROM
Designjet 3000 – 010101 error An Action Outside The EEROM Limits Has Been Performed
Designjet 3000 – 010102 error Physical EEROM Write And/Or Write Operations Failed. The EEROM Data That Is Written Does Not Match The Data That Is Read
Designjet 3000 – 010110 error The Content Of The Permanent Configuration Area Of The EEROM Is Not Valid When The Printer Is initialised In Service Mode
Designjet 3000 – 010111 error The Content Of The User Configuration Area EEROM Is Not Valid When The Printer Is initialised
Designjet 3000 – 010120 error The Content Of The Permanent Configuration Area Of The EERom Is Not Valid When Printer Is initialised In Normal Mode
Designjet 3000 – 010121 error One Of The Banks Of The User Area Was Corrupted While Writing Or Reading In That Area
Designjet 3000 – 030000 error Error In Finding The Primer Home Position
Designjet 3000 – 030001 error Error In Finding The Elevator Home Position
Designjet 3000 – 030002 error Error In Finding The Refill Arm Home Position
Designjet 3000 – 030003 error Error In Finding The refill Stepper Motor Home Position
Designjet 3000 – 030004 error Error In Finding The Service Station Home Position
Designjet 3000 – 030005 error Elevator Has A Problem Reaching A Desired Position
Designjet 3000 – 030006 error The Refill Position In The Y-axis In Not Calibrated
Designjet 3000 – 020010 error Problem With Fine Movement of The Y-Axis Motor
Designjet 3000 – 020011 error Error During Initialization Of The Y-Axis
Designjet 3000 – 040xxx error MIO Card Error
Designjet 3000 – 040601 error The MIO Card Does Not Support The MIO – 6 Protocol Cards With Vision – 5 Or Below Can Not Be Used With The Plotter. Version – 5.1 Cards Behave As Expected But Does Not Support PML Intructions
Designjet 3000 – 050000 error The Line Sensor Has Problems Finding The Mark Encoder
Designjet 3000 – 060000 error Th Line Sensor Is Not Functioning Properly Because There Is To Much Ambient Light
Designjet 3000 – 060200 error Incompatible Firmware And Carriage PCA
Designjet 3000 – 060399 error Incompatible Firmware And Line Sensor
Designjet 3000 – 07xxxx error Firmware Error
Designjet 3000 – 08xxxx error PostScript Error
Designjet 3000 – 080001 error Hard Disk Drive Installed Without PostScript
Designjet 3000 – 09xxxx error Problem With The Hard Disk
Designjet 3000 – 09004 error PostScript Installed Without The Hard Disk Drive
Designjet 3500 – 010020 error The CheckSum Read On The Flash SIMM Is InCorrect
Designjet 3500 – 010021 error The Base DRAM Or The RAM SIMM Tests Failed
Designjet 3500 – 010022 error The SWATH RAM Test Failed
Designjet 3500 – 010023 error A Fuse On The Main PCA Has Blown
Designjet 3500 – 010025 error Problem Initializing The Encoder Pulse Generator
Designjet 3500 – 010030 error One Of The Two Interconnect Boards Not Detected
Designjet 3500 – 010031 error The Printhead Primitive Driver ASIC Test Failed
Designjet 3500 – 010032 error Fan Test Failed – Current Not Detected In One Or Both Fans
Designjet 3500 – 010033 error The DC Motor ASIC Test Failed
Designjet 3500 – 010034 error One Of The DC Motor Has Failed
Designjet 3500 – 010035 error One Of The Stepper Motors Has Failed
Designjet 3500 – 010036 error ADC Test Failure In The Main PCA
Designjet 3500 – 010037 error ADC Test Failure In The Carriage PCA
Designjet 3500 – 010038 error A Printhead Voltage Could Not Be Set – Main PCA Failure
Designjet 3500 – 010039 error A Printhead Voltage Could Not Be Set – Carriage PCA Failure
Designjet 3500 – 010040 error The Amnient Temperture Measured Is Out Of The Normal Range
Designjet 3500 – 010041 error Problem In Setting The Printhead Voltage
Designjet 3500 – 010042 error The Status Of One Of The Optical Sensors Is Not Stable When It Should Be
Designjet 3500 – 010100 error Error Reading In The EEROM
Designjet 3500 – 010101 error An Action Outside The EEROM Limits Has Been Performed
Designjet 3500 – 010102 error Physical EEROM Write And/Or Write Operations Failed. The EEROM Data That Is Written Does Not Match The Data That Is Read
Designjet 3500 – 010110 error The Content Of The Permanent Configuration Area Of The EEROM Is Not Valid When The Printer Is initialised In Service Mode
Designjet 3500 – 010111 error The Content Of The User Configuration Area EEROM Is Not Valid When The Printer Is initialised
Designjet 3500 – 010120 error The Content Of The Permanent Configuration Area Of The EERom Is Not Valid When Printer Is initialised In Normal Mode
Designjet 3500 – 010121 error One Of The Banks Of The User Area Was Corrupted While Writing Or Reading In That Area
Designjet 3500 – 035000 error Error In Finding The Primer Home Position
Designjet 3500 – 035001 error Error In Finding The Elevator Home Position
Designjet 3500 – 035002 error Error In Finding The Refill Arm Home Position
Designjet 3500 – 035003 error Error In Finding The refill Stepper Motor Home Position
Designjet 3500 – 035004 error Error In Finding The Service Station Home Position
Designjet 3500 – 035005 error Elevator Has A Problem Reaching A Desired Position
Designjet 3500 – 035006 error The Refill Position In The Y-axis In Not Calibrated
Designjet 3500 – 020010 error Problem With Fine Movement of The Y-Axis Motor
Designjet 3500 – 020011 error Error During Initialization Of The Y-Axis
Designjet 3500 – 040xxx error MIO Card Error
Designjet 3500 – 040601 error The MIO Card Does Not Support The MIO – 6 Protocol Cards With Vision – 5 Or Below Can Not Be Used With The Plotter. Version – 5.1 Cards Behave As Expected But Does Not Support PML Intructions
Designjet 3500 – 050000 error The Line Sensor Has Problems Finding The Mark Encoder
Designjet 3500 – 060000 error Th Line Sensor Is Not Functioning Properly Because There Is To Much Ambient Light
Designjet 3500 – 060200 error Incompatible Firmware And Carriage PCA
Designjet 3500 – 060399 error Incompatible Firmware And Line Sensor
Designjet 3500 – 07xxxx error Firmware Error
Designjet 3500 – 08xxxx error PostScript Error
Designjet 3500 – 080001 error Hard Disk Drive Installed Without PostScript
Designjet 3500 – 09xxxx error Problem With The Hard Disk
Designjet 3500 – 09004 error PostScript Installed Without The Hard Disk Drive